Shop headings: New Spares | Used Spares | Accessories | Brands
Distributor cap
May be supplied in black
This part is due back in stock soon, call 01484 841395 to reserve yours
12715432 GU12715432 12 71 54 32
1271 5432 1271.5432 12.71.54.32
£22.00
INC VAT
£18.33 EX VAT
Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors
This part is due back in stock soon, call 01484 841395 to reserve yours
12732500 GU12732500 12 73 25 00
1273 2500 1273.2500 12.73.25.00
£30.90
INC VAT
£25.75 EX VAT
Oil pressure switch M12 thread, male spade connector
Superceded by ELA19670 . See ENA12640 for replacement crush washer if required
Sorry, this part is no longer available.
12768700 GU12768700 12 76 87 00
1276 8700 1276.8700 12.76.87.00
Sorry this item is out of production
Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils
Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit
This part is due back in stock soon, call 01484 841395 to reserve yours
£28.00
INC VAT
£23.33 EX VAT
Protective cap for battery lead
This part is due back in stock soon, call 01484 841395 to reserve yours
25707100-z 25707100 GU25707100 25 70 71 00
2570 7100 2570.7100 25.70.71.00
£2.00
INC VAT
£1.67 EX VAT
Push button starter switch, chrome finish body, screw contacts to rear
This part is available by special order, request a quote
26735001-z 26735001 GU26735001 26 73 50 01
2673 5001 2673.5001 26.73.50.01
£19.80
INC VAT
£16.50 EX VAT
12 volt single output 3 Ohm ignition coil (lead to distributor)
Push fit HT lead, see ELA00001 for crimp on HT lead connector. Supplied without coil clamp
This part is due back in stock soon, call 01484 841395 to reserve yours
26716504 GU26716504 26 71 65 04
2671 6504 2671.6504 26.71.65.04
£58.00
INC VAT
£48.33 EX VAT
Silca key blank for ignition key, match profile to your existing key
This part is due back in stock soon, call 01484 841395 to reserve yours
NE5
£4.20
INC VAT
£3.50 EX VAT
Silca key blank for ignition key, match profile to your existing key
This part is due back in stock soon, call 01484 841395 to reserve yours
£4.20
INC VAT
£3.50 EX VAT
Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.
This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address.
NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts.
Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place
Supercedes Guzzi refs. 12730705, 14730554 and 14730705
30730711 GU30730711 30 73 07 11
3073 0711 3073.0711 30.73.07.11
£155.00
INC VAT
£129.17 EX VAT